From max_and_tnt at hotmail.com Tue Jul 1 23:55:02 2003 From: max_and_tnt at hotmail.com (Joe Max) Date: Tue Jan 18 13:57:49 2005 Subject: [Ascend] Re: (ASCEND) E1 Problem Message-ID: There are a couple of things that come to mind: 1) the max is not hash-coded correctly. Check on the status window, for the enabled features. 2) some maxes were hash-coded to disable the use of S56 modems. 3) I'm not sure whether E1-R2 needs it, but if the max can't determine the type of call, it will assume that it is a digital call. If E1-R2 doesn't tell the MAX the type of call, then you need to force it by specifying 'Slot=3' on each and every one of the E1 channels. Beware though that this setup prevents you from taking analog and digital calls. If you are going to take analog and digital calls, you need a true PRI line. Hope some of this helps, -J >I bought an Ascend MAX 4000 with 2 S56 modem cards. I connected the E1 >from telco to the unit and configured it (R2 signalling and CAS switch, >G.703 switch as the Telco told me). The problem is it does not answer. >(users need to dial from Analog modems to this E1 line). When I dial the >E1 number from analog phone, it waits for about 45 seconds and then gives >a timeout tone. I have tried every possible parameters with no luck. >Currently, the status shows L1/TE. Can someone help me make this work? ++ Ascend Users Mailing List ++ To unsubscribe: send unsubscribe to ascend-users-request@bungi.com Archives: http://www.nexial.com/mailinglists/ From drew at orbityl.com Thu Jul 3 19:35:01 2003 From: drew at orbityl.com (Drew Weaver) Date: Tue Jan 18 13:57:49 2005 Subject: [Ascend] (ASCEND) Max4048 question, Message-ID: <007401c341be$5da63070$0500010a@BLACKULA> Hi, which software load to I need to be able to turn on clock sourcing in the trunk configuration? Right now it says CLOCK SOURCE=n/a but I need it to be yes like it is on all of my other max4048s. Thanks, -Drew ++ Ascend Users Mailing List ++ To unsubscribe: send unsubscribe to ascend-users-request@bungi.com Archives: http://www.nexial.com/mailinglists/ From ib at indiver.com Sat Jul 5 02:00:02 2003 From: ib at indiver.com (Indiver Badal) Date: Tue Jan 18 13:57:49 2005 Subject: [Ascend] (ASCEND) Line Quality - E1 & Series56 In-Reply-To: References: Message-ID: When users dial-in to my Max 4000 (all users are anolog modem users, we dont need isdn etc.), the modem takes very long time to handshake and mostly it fails to connect after about a minute. I tried various AT answer strings but no good result. When I checked the modem diagnostics, it showed a very poor Line Quality and RX level. But when I put the same E1 line into other RAS servers (working Patton and Total Control), it works just fine, the line quality shows very good. Could this be an incompatibility issue? I have checked with the Telco (the telco uses Siemens switches, though I dont know other details) and they have no such complaints for any other E1 connections. Any help will be highly appreciated. Thanks Indiver ++ Ascend Users Mailing List ++ To unsubscribe: send unsubscribe to ascend-users-request@bungi.com Archives: http://www.nexial.com/mailinglists/ From ib at indiver.com Sat Jul 5 02:01:01 2003 From: ib at indiver.com (Indiver Badal) Date: Tue Jan 18 13:57:49 2005 Subject: [Ascend] (ASCEND) MAX 4000 Jumpers In-Reply-To: References: Message-ID: Page 38 of MAX 4000 H/W installation guide refers to jumpers inside the chassis for selecting Impedance. Can anyone tell me where to find those jumpers? jumper number? and also how to set them to 120/75/50 ohm? Any help will be highly appreciated. Thanks Indiver ++ Ascend Users Mailing List ++ To unsubscribe: send unsubscribe to ascend-users-request@bungi.com Archives: http://www.nexial.com/mailinglists/ From ahmiqs at yahoo.com Sat Jul 5 08:53:01 2003 From: ahmiqs at yahoo.com (Schahzad Zafar) Date: Tue Jan 18 13:57:49 2005 Subject: [Ascend] (ASCEND) Call routing Maxtnt In-Reply-To: Message-ID: <20030705134440.83261.qmail@web12105.mail.yahoo.com> Hi hopes every one be fine.I need a little help.Is there any method to route incoming calls to some other Maxtnt. the situation here is like this E1/pri local circuit User ----> Maxtnt 1----------------> maxtnt 2 Now my users are getting login to Maxtnt 1 , i want to change this thing that user login to Maxtnt 2. So what could be the option ? is there some device or Max's card which support call routing to some other Max tnt.If any one know any material about call routing i ll highly appreciate the help. Thanx & Regards ===== Schahzad Zafar System Administrator Brain NET NWFP Pakistan schahzad@brain.net.pk 0300-5930233 __________________________________ Do you Yahoo!? SBC Yahoo! DSL - Now only $29.95 per month! http://sbc.yahoo.com ++ Ascend Users Mailing List ++ To unsubscribe: send unsubscribe to ascend-users-request@bungi.com Archives: http://www.nexial.com/mailinglists/ From ahmiqs at yahoo.com Sat Jul 5 08:53:02 2003 From: ahmiqs at yahoo.com (Schahzad Zafar) Date: Tue Jan 18 13:57:49 2005 Subject: [Ascend] Re: (ASCEND) Re: disconnected users In-Reply-To: Message-ID: <20030705134250.66359.qmail@web12108.mail.yahoo.com> Hi hopes every one be fine.I need a little help.Is there any method to route incoming calls to some other Maxtnt. the situation here is like this E1/pri local circuit User ----> Maxtnt 1----------------> maxtnt 2 Now my users are getting login to Maxtnt 1 , i want to change this thing that user login to Maxtnt 2. So what could be the option ? is there some device or Max's card which support call routing to some other Max tnt.If any one know any material about call routing i ll highly appreciate the help. Thanx & Regards ===== Schahzad Zafar System Administrator Brain NET NWFP Pakistan schahzad@brain.net.pk 0300-5930233 __________________________________ Do you Yahoo!? SBC Yahoo! DSL - Now only $29.95 per month! http://sbc.yahoo.com ++ Ascend Users Mailing List ++ To unsubscribe: send unsubscribe to ascend-users-request@bungi.com Archives: http://www.nexial.com/mailinglists/ From frnana at yahoo.com Sun Jul 6 05:01:01 2003 From: frnana at yahoo.com (nana) Date: Tue Jan 18 13:57:49 2005 Subject: [Ascend] (ASCEND) Usaha Sampingan Tanpa Beban Message-ID: <200307060947.h669lDd13556@smtp2.sby.rad.net.id> MLM yang bersifat Tutup Point (TUPO) selalu memberatkan anggota/distributor apalagi harga produknya gak ada yg murah. Tapi tidak dengan bisnis yg satu ini, klik di http://serayumadiun.co-ltd.com Tanpa beresiko, krn pendaftaran hanya sekali saja seumur hidup dan cocok sekali untuk kalangan menengah ke bawah. Semoga website di email ini bisa berkenan untuk anda sebagai prospek bisnis sampingan yang menjanjikan. Aminn… Regards nana ++ Ascend Users Mailing List ++ To unsubscribe: send unsubscribe to ascend-users-request@bungi.com Archives: http://www.nexial.com/mailinglists/ From drew.weaver at thenap.com Mon Jul 7 11:57:01 2003 From: drew.weaver at thenap.com (Drew Weaver) Date: Tue Jan 18 13:57:50 2005 Subject: [Ascend] (ASCEND) Max help, please, someone out there must know something about the se boxes. Message-ID: <75634F04BFCFD511BF69009027DC864948455F@mailman.thenap.com> I'm willing to pay someone who considers themselves an oracle of knowledge about Max NAS equipment, I really need some help with the following situation. My company was hired on a consulting basis to see if we could help another ISP in a rural community with a problem they were having, basically their situation is this. They have 2 Max 6000s (one has 4 modem cards, one has 2 [96 + 48]) they have 5 T1s (they aren't ISDN t1s, like 23 channels) they're some kind of funky rural T1, I've never seen before, the kind we use are the 24 channels, 1 used for d channel type. Ok so here is the issue. If all of their lines are enabled at once, their callers get a loud squeeling sound instead of a modem when they dial, and the maxes say -c-cc-cc-c instead of ------- or --*-*-*** et cetera. The phone company says their lines are clear, I even tried taking down one of our old max 4048s from the basement and plugging that in to see whats going on but that max 4048 wont even bring up their lines, I guess the 4048s have different wan interface cards in them than the 6000s do? Whats weird about this scenario is that my max4048 doesn't have the Front end = csu option, but their 6000s do, and ascend's documentation say that this is required. Anyway im having lots of problems with this and I need some help. Thanks, -Drew ++ Ascend Users Mailing List ++ To unsubscribe: send unsubscribe to ascend-users-request@bungi.com Archives: http://www.nexial.com/mailinglists/ From tiger at zoomph.net Mon Jul 7 13:49:01 2003 From: tiger at zoomph.net (Craig Salmond) Date: Tue Jan 18 13:57:50 2005 Subject: [Ascend] Re: (ASCEND) Max help, please, someone out there must know something about the se boxes. In-Reply-To: <75634F04BFCFD511BF69009027DC864948455F@mailman.thenap.com> Message-ID: On Mon, 7 Jul 2003, Drew Weaver wrote: Drew, First ask the telco if these are PRI's (each T1 has 23 B channels and 1 D Channel), If they are PRI's with NFAS signaling (each T1 has 24 B channels, but one of T1 has 23 B's and 1D) or if they are Channelized T1's all 24 B channels }Ok so here is the issue. If all of their lines are enabled at once, their }this scenario is that my max4048 doesn't have the Front end = csu option, }but their 6000s do, and ascend's documentation say that this is required. The squel is probably the HDLC tone, as it things all inbound calls are ISDN, not voice (data) Craig Hurricane Computer Cables Quality Computer Sales & Repair Cables, and Computer Accessories 352-483-2306 Voice M-F 9a-6p Sat 11a-4p 352-357-0381 Fax http://www.hurricane-computers.com ++ Ascend Users Mailing List ++ To unsubscribe: send unsubscribe to ascend-users-request@bungi.com Archives: http://www.nexial.com/mailinglists/ From drew.weaver at thenap.com Mon Jul 7 14:04:01 2003 From: drew.weaver at thenap.com (Drew Weaver) Date: Tue Jan 18 13:57:50 2005 Subject: [Ascend] (ASCEND) max issue: update Message-ID: <75634F04BFCFD511BF69009027DC8649484575@mailman.thenap.com> Hi, Ok I got it kind of working properly. Disabling the max that has only the 1 T1 in it has completely eliminated the squeal, but now I have a goofy problem. There are 35 users online, but I see people coming in and going out like mad, so its almost like everytime a new user signs on, another user gets kicked off. Ya know what I mean? Say user b Is logged on, and user C logs in, user b gets kicked off so that user c can get on, does this make sense? -Drew ++ Ascend Users Mailing List ++ To unsubscribe: send unsubscribe to ascend-users-request@bungi.com Archives: http://www.nexial.com/mailinglists/ From drew.weaver at thenap.com Mon Jul 7 15:01:01 2003 From: drew.weaver at thenap.com (Drew Weaver) Date: Tue Jan 18 13:57:51 2005 Subject: [Ascend] (ASCEND) Ok ;-) I think the lines are configured properly, but. Message-ID: <75634F04BFCFD511BF69009027DC8649484581@mailman.thenap.com> I'm kind of paranoid at one point I saw the number of users go up to 49, and now its back down to 37, you wouldn't think that the number of users would vary that much from hour to hour would you? Here are the disconnect cause codes for the last 30 minutes: 07/07/2003 14:02:19 Ascend-Disconnect-Cause : Integer Value = 185 07/07/2003 14:02:22 Ascend-Disconnect-Cause : Integer Value = 185 07/07/2003 14:02:51 Ascend-Disconnect-Cause : Integer Value = 185 07/07/2003 14:03:14 Ascend-Disconnect-Cause : Integer Value = 185 07/07/2003 14:03:25 Ascend-Disconnect-Cause : Integer Value = 185 07/07/2003 14:03:31 Ascend-Disconnect-Cause : Integer Value = 185 07/07/2003 14:03:49 Ascend-Disconnect-Cause : Integer Value = 185 07/07/2003 14:04:06 Ascend-Disconnect-Cause : Integer Value = 185 07/07/2003 14:04:14 Ascend-Disconnect-Cause : Integer Value = 185 07/07/2003 14:04:16 Ascend-Disconnect-Cause : Integer Value = 185 07/07/2003 14:04:51 Ascend-Disconnect-Cause : Integer Value = 185 07/07/2003 14:05:17 Ascend-Disconnect-Cause : Integer Value = 45 07/07/2003 14:05:25 Ascend-Disconnect-Cause : Integer Value = 11 07/07/2003 14:05:41 Ascend-Disconnect-Cause : Integer Value = 45 07/07/2003 14:05:48 Ascend-Disconnect-Cause : Integer Value = 185 07/07/2003 14:05:50 Ascend-Disconnect-Cause : Integer Value = 185 07/07/2003 14:05:56 Ascend-Disconnect-Cause : Integer Value = 100 07/07/2003 14:05:59 Ascend-Disconnect-Cause : Integer Value = 185 07/07/2003 14:06:05 Ascend-Disconnect-Cause : Integer Value = 185 07/07/2003 14:06:52 Ascend-Disconnect-Cause : Integer Value = 185 07/07/2003 14:06:53 Ascend-Disconnect-Cause : Integer Value = 185 07/07/2003 14:06:56 Ascend-Disconnect-Cause : Integer Value = 185 07/07/2003 14:06:57 Ascend-Disconnect-Cause : Integer Value = 185 07/07/2003 14:07:19 Ascend-Disconnect-Cause : Integer Value = 45 07/07/2003 14:07:22 Ascend-Disconnect-Cause : Integer Value = 185 07/07/2003 14:07:22 Ascend-Disconnect-Cause : Integer Value = 185 07/07/2003 14:07:22 Ascend-Disconnect-Cause : Integer Value = 185 07/07/2003 14:07:22 Ascend-Disconnect-Cause : Integer Value = 185 07/07/2003 14:07:22 Ascend-Disconnect-Cause : Integer Value = 185 07/07/2003 14:07:22 Ascend-Disconnect-Cause : Integer Value = 185 07/07/2003 14:07:22 Ascend-Disconnect-Cause : Integer Value = 185 07/07/2003 14:07:22 Ascend-Disconnect-Cause : Integer Value = 185 07/07/2003 14:07:22 Ascend-Disconnect-Cause : Integer Value = 185 07/07/2003 14:07:22 Ascend-Disconnect-Cause : Integer Value = 185 07/07/2003 14:07:22 Ascend-Disconnect-Cause : Integer Value = 185 07/07/2003 14:07:23 Ascend-Disconnect-Cause : Integer Value = 185 07/07/2003 14:07:23 Ascend-Disconnect-Cause : Integer Value = 185 07/07/2003 14:07:23 Ascend-Disconnect-Cause : Integer Value = 185 07/07/2003 14:07:23 Ascend-Disconnect-Cause : Integer Value = 185 07/07/2003 14:07:23 Ascend-Disconnect-Cause : Integer Value = 185 07/07/2003 14:07:33 Ascend-Disconnect-Cause : Integer Value = 185 07/07/2003 14:07:53 Ascend-Disconnect-Cause : Integer Value = 185 07/07/2003 14:08:11 Ascend-Disconnect-Cause : Integer Value = 185 07/07/2003 14:08:34 Ascend-Disconnect-Cause : Integer Value = 45 07/07/2003 14:09:19 Ascend-Disconnect-Cause : Integer Value = 185 07/07/2003 14:09:21 Ascend-Disconnect-Cause : Integer Value = 185 07/07/2003 14:09:25 Ascend-Disconnect-Cause : Integer Value = 185 07/07/2003 14:09:29 Ascend-Disconnect-Cause : Integer Value = 185 07/07/2003 14:09:37 Ascend-Disconnect-Cause : Integer Value = 45 07/07/2003 14:10:00 Ascend-Disconnect-Cause : Integer Value = 45 07/07/2003 14:10:20 Ascend-Disconnect-Cause : Integer Value = 45 07/07/2003 14:10:25 Ascend-Disconnect-Cause : Integer Value = 45 07/07/2003 14:10:38 Ascend-Disconnect-Cause : Integer Value = 185 07/07/2003 14:11:24 Ascend-Disconnect-Cause : Integer Value = 45 07/07/2003 14:13:43 Ascend-Disconnect-Cause : Integer Value = 42 07/07/2003 14:14:09 Ascend-Disconnect-Cause : Integer Value = 185 07/07/2003 14:14:25 Ascend-Disconnect-Cause : Integer Value = 11 07/07/2003 14:14:28 Ascend-Disconnect-Cause : Integer Value = 42 07/07/2003 14:14:42 Ascend-Disconnect-Cause : Integer Value = 45 07/07/2003 14:15:19 Ascend-Disconnect-Cause : Integer Value = 42 07/07/2003 14:15:39 Ascend-Disconnect-Cause : Integer Value = 42 07/07/2003 14:15:46 Ascend-Disconnect-Cause : Integer Value = 45 07/07/2003 14:16:18 Ascend-Disconnect-Cause : Integer Value = 42 07/07/2003 14:16:25 Ascend-Disconnect-Cause : Integer Value = 45 07/07/2003 14:16:54 Ascend-Disconnect-Cause : Integer Value = 185 07/07/2003 14:17:36 Ascend-Disconnect-Cause : Integer Value = 45 07/07/2003 14:17:36 Ascend-Disconnect-Cause : Integer Value = 42 07/07/2003 14:17:38 Ascend-Disconnect-Cause : Integer Value = 185 07/07/2003 14:18:55 Ascend-Disconnect-Cause : Integer Value = 100 07/07/2003 14:19:10 Ascend-Disconnect-Cause : Integer Value = 45 07/07/2003 14:19:24 Ascend-Disconnect-Cause : Integer Value = 100 07/07/2003 14:19:25 Ascend-Disconnect-Cause : Integer Value = 185 07/07/2003 14:20:44 Ascend-Disconnect-Cause : Integer Value = 100 07/07/2003 14:21:34 Ascend-Disconnect-Cause : Integer Value = 45 07/07/2003 14:22:31 Ascend-Disconnect-Cause : Integer Value = 45 07/07/2003 14:23:02 Ascend-Disconnect-Cause : Integer Value = 45 07/07/2003 14:23:32 Ascend-Disconnect-Cause : Integer Value = 100 07/07/2003 14:23:49 Ascend-Disconnect-Cause : Integer Value = 185 07/07/2003 14:24:36 Ascend-Disconnect-Cause : Integer Value = 45 07/07/2003 14:25:04 Ascend-Disconnect-Cause : Integer Value = 45 07/07/2003 14:25:37 Ascend-Disconnect-Cause : Integer Value = 11 07/07/2003 14:25:53 Ascend-Disconnect-Cause : Integer Value = 185 07/07/2003 14:26:07 Ascend-Disconnect-Cause : Integer Value = 11 07/07/2003 14:27:40 Ascend-Disconnect-Cause : Integer Value = 45 07/07/2003 14:28:19 Ascend-Disconnect-Cause : Integer Value = 185 07/07/2003 14:29:04 Ascend-Disconnect-Cause : Integer Value = 11 07/07/2003 14:29:14 Ascend-Disconnect-Cause : Integer Value = 45 07/07/2003 14:30:08 Ascend-Disconnect-Cause : Integer Value = 45 07/07/2003 14:30:35 Ascend-Disconnect-Cause : Integer Value = 45 07/07/2003 14:30:55 Ascend-Disconnect-Cause : Integer Value = 45 07/07/2003 14:31:51 Ascend-Disconnect-Cause : Integer Value = 45 07/07/2003 14:32:34 Ascend-Disconnect-Cause : Integer Value = 45 07/07/2003 14:35:14 Ascend-Disconnect-Cause : Integer Value = 100 07/07/2003 14:35:58 Ascend-Disconnect-Cause : Integer Value = 11 07/07/2003 14:37:56 Ascend-Disconnect-Cause : Integer Value = 45 07/07/2003 14:38:57 Ascend-Disconnect-Cause : Integer Value = 185 07/07/2003 14:40:55 Ascend-Disconnect-Cause : Integer Value = 45 07/07/2003 14:41:38 Ascend-Disconnect-Cause : Integer Value = 45 07/07/2003 14:42:40 Ascend-Disconnect-Cause : Integer Value = 45 07/07/2003 14:42:49 Ascend-Disconnect-Cause : Integer Value = 185 07/07/2003 14:43:39 Ascend-Disconnect-Cause : Integer Value = 45 07/07/2003 14:44:55 Ascend-Disconnect-Cause : Integer Value = 45 07/07/2003 14:45:02 Ascend-Disconnect-Cause : Integer Value = 45 07/07/2003 14:45:15 Ascend-Disconnect-Cause : Integer Value = 45 07/07/2003 14:47:20 Ascend-Disconnect-Cause : Integer Value = 100 07/07/2003 14:47:20 Ascend-Disconnect-Cause : Integer Value = 45 07/07/2003 14:48:22 Ascend-Disconnect-Cause : Integer Value = 45 07/07/2003 14:48:48 Ascend-Disconnect-Cause : Integer Value = 45 07/07/2003 14:49:22 Ascend-Disconnect-Cause : Integer Value = 45 07/07/2003 14:49:36 Ascend-Disconnect-Cause : Integer Value = 45 07/07/2003 14:50:57 Ascend-Disconnect-Cause : Integer Value = 11 07/07/2003 14:51:48 Ascend-Disconnect-Cause : Integer Value = 45 07/07/2003 14:51:56 Ascend-Disconnect-Cause : Integer Value = 45 07/07/2003 14:52:10 Ascend-Disconnect-Cause : Integer Value = 45 07/07/2003 14:52:12 Ascend-Disconnect-Cause : Integer Value = 185 07/07/2003 14:52:55 Ascend-Disconnect-Cause : Integer Value = 45 07/07/2003 14:54:25 Ascend-Disconnect-Cause : Integer Value = 45 07/07/2003 14:55:27 Ascend-Disconnect-Cause : Integer Value = 185 07/07/2003 14:55:58 Ascend-Disconnect-Cause : Integer Value = 45 07/07/2003 14:56:08 Ascend-Disconnect-Cause : Integer Value = 185 07/07/2003 14:56:48 Ascend-Disconnect-Cause : Integer Value = 45 07/07/2003 14:56:58 Ascend-Disconnect-Cause : Integer Value = 45 07/07/2003 14:59:55 Ascend-Disconnect-Cause : Integer Value = 45 07/07/2003 15:00:16 Ascend-Disconnect-Cause : Integer Value = 45 07/07/2003 15:00:28 Ascend-Disconnect-Cause : Integer Value = 185 07/07/2003 15:00:32 Ascend-Disconnect-Cause : Integer Value = 45 07/07/2003 15:02:07 Ascend-Disconnect-Cause : Integer Value = 45 07/07/2003 15:02:16 Ascend-Disconnect-Cause : Integer Value = 45 07/07/2003 15:03:05 Ascend-Disconnect-Cause : Integer Value = 45 07/07/2003 15:03:44 Ascend-Disconnect-Cause : Integer Value = 41 07/07/2003 15:04:24 Ascend-Disconnect-Cause : Integer Value = 185 07/07/2003 15:04:30 Ascend-Disconnect-Cause : Integer Value = 100 07/07/2003 15:05:03 Ascend-Disconnect-Cause : Integer Value = 45 07/07/2003 15:06:10 Ascend-Disconnect-Cause : Integer Value = 100 07/07/2003 15:06:16 Ascend-Disconnect-Cause : Integer Value = 45 07/07/2003 15:07:03 Ascend-Disconnect-Cause : Integer Value = 100 07/07/2003 15:07:21 Ascend-Disconnect-Cause : Integer Value = 45 07/07/2003 15:07:25 Ascend-Disconnect-Cause : Integer Value = 45 07/07/2003 15:08:24 Ascend-Disconnect-Cause : Integer Value = 45 07/07/2003 15:08:28 Ascend-Disconnect-Cause : Integer Value = 11 07/07/2003 15:08:41 Ascend-Disconnect-Cause : Integer Value = 45 07/07/2003 15:09:39 Ascend-Disconnect-Cause : Integer Value = 185 07/07/2003 15:10:58 Ascend-Disconnect-Cause : Integer Value = 45 07/07/2003 15:12:07 Ascend-Disconnect-Cause : Integer Value = 45 07/07/2003 15:12:30 Ascend-Disconnect-Cause : Integer Value = 45 07/07/2003 15:13:14 Ascend-Disconnect-Cause : Integer Value = 185 07/07/2003 15:13:26 Ascend-Disconnect-Cause : Integer Value = 45 07/07/2003 15:14:00 Ascend-Disconnect-Cause : Integer Value = 45 07/07/2003 15:14:49 Ascend-Disconnect-Cause : Integer Value = 45 07/07/2003 15:14:51 Ascend-Disconnect-Cause : Integer Value = 185 07/07/2003 15:15:00 Ascend-Disconnect-Cause : Integer Value = 45 07/07/2003 15:15:01 Ascend-Disconnect-Cause : Integer Value = 45 07/07/2003 15:15:19 Ascend-Disconnect-Cause : Integer Value = 185 07/07/2003 15:16:28 Ascend-Disconnect-Cause : Integer Value = 185 07/07/2003 15:16:32 Ascend-Disconnect-Cause : Integer Value = 185 07/07/2003 15:16:45 Ascend-Disconnect-Cause : Integer Value = 42 07/07/2003 15:17:17 Ascend-Disconnect-Cause : Integer Value = 45 07/07/2003 15:17:23 Ascend-Disconnect-Cause : Integer Value = 10 07/07/2003 15:17:29 Ascend-Disconnect-Cause : Integer Value = 42 07/07/2003 15:17:38 Ascend-Disconnect-Cause : Integer Value = 185 07/07/2003 15:17:52 Ascend-Disconnect-Cause : Integer Value = 100 07/07/2003 15:18:39 Ascend-Disconnect-Cause : Integer Value = 45 07/07/2003 15:19:03 Ascend-Disconnect-Cause : Integer Value = 45 07/07/2003 15:19:07 Ascend-Disconnect-Cause : Integer Value = 45 Sorry for the long post, I just wanted to see if you guys feel that this is what I should be seeing as far as disconnect codes for the last half hour assuming everything is good. -Drew ++ Ascend Users Mailing List ++ To unsubscribe: send unsubscribe to ascend-users-request@bungi.com Archives: http://www.nexial.com/mailinglists/ From skipmax at seacove.net Mon Jul 7 15:10:02 2003 From: skipmax at seacove.net (Dennis Duval) Date: Tue Jan 18 13:57:51 2005 Subject: [Ascend] Re: (ASCEND) max issue: update References: <75634F04BFCFD511BF69009027DC8649484575@mailman.thenap.com> Message-ID: <008201c344c2$0a333c60$0a01a8c0@barny> Drew Weaver wrote: > Hi, Ok I got it kind of working properly. Disabling > the max that has only the 1 T1 in it has completely > eliminated the squeal, but now I have a goofy problem. > > There are 35 users online, but I see people coming in and > going out like mad, so its almost like everytime a new > user signs on, another user gets kicked off. > Are all the sessions very short? If so, the sessions are probably not getting completely established. You might check your Net/T1--> Line Config -->Factory-->Line x-->Rob Ctl = Some central switches like this set to "Wink-Start" and others like "Inc-W-200" You asked about the wan interfaces on 6000 versus 4000's. They are the same as far as I know. I have used PRI and CHT1 on both, and as long as they are configured the same, they should be interchangable. There are few options that are different, but I believe there is nothing that would keep you from using the line with either series of maxen. As a previous respondent stated, you need to know the type of T1. Is it PRI or CHT1? If its CHT1, you need to know the Framing Mode and Encoding. If you can find out the above information, I will be glad to compare settings with you over the phone. Email me off list to get my phone number. Dennis Duval Dennis Duval ++ Ascend Users Mailing List ++ To unsubscribe: send unsubscribe to ascend-users-request@bungi.com Archives: http://www.nexial.com/mailinglists/ From tiger at zoomph.net Mon Jul 7 16:20:02 2003 From: tiger at zoomph.net (Craig Salmond) Date: Tue Jan 18 13:57:51 2005 Subject: [Ascend] Re: (ASCEND) Ok ;-) I think the lines are configured properly, but. In-Reply-To: <75634F04BFCFD511BF69009027DC8649484581@mailman.thenap.com> Message-ID: On Mon, 7 Jul 2003, Drew Weaver wrote: 45's are normal cleaning. 185 is no reason specified (Far end hung up) [Line noise, customer picked up extention] } I'm kind of paranoid at one point I saw the number of users go up to }49, and now its back down to 37, you wouldn't think that the number of users }would vary that much from hour to hour would you? } }Here are the disconnect cause codes for the last 30 minutes: } }07/07/2003 14:02:19 Ascend-Disconnect-Cause : Integer Value = 185 }07/07/2003 14:02:22 Ascend-Disconnect-Cause : Integer Value = 185 }07/07/2003 14:02:51 Ascend-Disconnect-Cause : Integer Value = 185 }07/07/2003 14:03:14 Ascend-Disconnect-Cause : Integer Value = 185 }07/07/2003 14:03:25 Ascend-Disconnect-Cause : Integer Value = 185 }07/07/2003 14:03:31 Ascend-Disconnect-Cause : Integer Value = 185 }07/07/2003 14:03:49 Ascend-Disconnect-Cause : Integer Value = 185 }07/07/2003 14:04:06 Ascend-Disconnect-Cause : Integer Value = 185 }07/07/2003 14:04:14 Ascend-Disconnect-Cause : Integer Value = 185 }07/07/2003 14:04:16 Ascend-Disconnect-Cause : Integer Value = 185 }07/07/2003 14:04:51 Ascend-Disconnect-Cause : Integer Value = 185 }07/07/2003 14:05:17 Ascend-Disconnect-Cause : Integer Value = 45 }07/07/2003 14:05:25 Ascend-Disconnect-Cause : Integer Value = 11 }07/07/2003 14:05:41 Ascend-Disconnect-Cause : Integer Value = 45 }07/07/2003 14:05:48 Ascend-Disconnect-Cause : Integer Value = 185 }07/07/2003 14:05:50 Ascend-Disconnect-Cause : Integer Value = 185 }07/07/2003 14:05:56 Ascend-Disconnect-Cause : Integer Value = 100 }07/07/2003 14:05:59 Ascend-Disconnect-Cause : Integer Value = 185 }07/07/2003 14:06:05 Ascend-Disconnect-Cause : Integer Value = 185 }07/07/2003 14:06:52 Ascend-Disconnect-Cause : Integer Value = 185 }07/07/2003 14:06:53 Ascend-Disconnect-Cause : Integer Value = 185 }07/07/2003 14:06:56 Ascend-Disconnect-Cause : Integer Value = 185 }07/07/2003 14:06:57 Ascend-Disconnect-Cause : Integer Value = 185 }07/07/2003 14:07:19 Ascend-Disconnect-Cause : Integer Value = 45 }07/07/2003 14:07:22 Ascend-Disconnect-Cause : Integer Value = 185 }07/07/2003 14:07:22 Ascend-Disconnect-Cause : Integer Value = 185 }07/07/2003 14:07:22 Ascend-Disconnect-Cause : Integer Value = 185 }07/07/2003 14:07:22 Ascend-Disconnect-Cause : Integer Value = 185 }07/07/2003 14:07:22 Ascend-Disconnect-Cause : Integer Value = 185 }07/07/2003 14:07:22 Ascend-Disconnect-Cause : Integer Value = 185 }07/07/2003 14:07:22 Ascend-Disconnect-Cause : Integer Value = 185 }07/07/2003 14:07:22 Ascend-Disconnect-Cause : Integer Value = 185 }07/07/2003 14:07:22 Ascend-Disconnect-Cause : Integer Value = 185 }07/07/2003 14:07:22 Ascend-Disconnect-Cause : Integer Value = 185 }07/07/2003 14:07:22 Ascend-Disconnect-Cause : Integer Value = 185 }07/07/2003 14:07:23 Ascend-Disconnect-Cause : Integer Value = 185 }07/07/2003 14:07:23 Ascend-Disconnect-Cause : Integer Value = 185 }07/07/2003 14:07:23 Ascend-Disconnect-Cause : Integer Value = 185 }07/07/2003 14:07:23 Ascend-Disconnect-Cause : Integer Value = 185 }07/07/2003 14:07:23 Ascend-Disconnect-Cause : Integer Value = 185 }07/07/2003 14:07:33 Ascend-Disconnect-Cause : Integer Value = 185 }07/07/2003 14:07:53 Ascend-Disconnect-Cause : Integer Value = 185 }07/07/2003 14:08:11 Ascend-Disconnect-Cause : Integer Value = 185 }07/07/2003 14:08:34 Ascend-Disconnect-Cause : Integer Value = 45 }07/07/2003 14:09:19 Ascend-Disconnect-Cause : Integer Value = 185 }07/07/2003 14:09:21 Ascend-Disconnect-Cause : Integer Value = 185 }07/07/2003 14:09:25 Ascend-Disconnect-Cause : Integer Value = 185 }07/07/2003 14:09:29 Ascend-Disconnect-Cause : Integer Value = 185 }07/07/2003 14:09:37 Ascend-Disconnect-Cause : Integer Value = 45 }07/07/2003 14:10:00 Ascend-Disconnect-Cause : Integer Value = 45 }07/07/2003 14:10:20 Ascend-Disconnect-Cause : Integer Value = 45 }07/07/2003 14:10:25 Ascend-Disconnect-Cause : Integer Value = 45 }07/07/2003 14:10:38 Ascend-Disconnect-Cause : Integer Value = 185 }07/07/2003 14:11:24 Ascend-Disconnect-Cause : Integer Value = 45 }07/07/2003 14:13:43 Ascend-Disconnect-Cause : Integer Value = 42 }07/07/2003 14:14:09 Ascend-Disconnect-Cause : Integer Value = 185 }07/07/2003 14:14:25 Ascend-Disconnect-Cause : Integer Value = 11 }07/07/2003 14:14:28 Ascend-Disconnect-Cause : Integer Value = 42 }07/07/2003 14:14:42 Ascend-Disconnect-Cause : Integer Value = 45 }07/07/2003 14:15:19 Ascend-Disconnect-Cause : Integer Value = 42 }07/07/2003 14:15:39 Ascend-Disconnect-Cause : Integer Value = 42 }07/07/2003 14:15:46 Ascend-Disconnect-Cause : Integer Value = 45 }07/07/2003 14:16:18 Ascend-Disconnect-Cause : Integer Value = 42 }07/07/2003 14:16:25 Ascend-Disconnect-Cause : Integer Value = 45 }07/07/2003 14:16:54 Ascend-Disconnect-Cause : Integer Value = 185 }07/07/2003 14:17:36 Ascend-Disconnect-Cause : Integer Value = 45 }07/07/2003 14:17:36 Ascend-Disconnect-Cause : Integer Value = 42 }07/07/2003 14:17:38 Ascend-Disconnect-Cause : Integer Value = 185 }07/07/2003 14:18:55 Ascend-Disconnect-Cause : Integer Value = 100 }07/07/2003 14:19:10 Ascend-Disconnect-Cause : Integer Value = 45 }07/07/2003 14:19:24 Ascend-Disconnect-Cause : Integer Value = 100 }07/07/2003 14:19:25 Ascend-Disconnect-Cause : Integer Value = 185 }07/07/2003 14:20:44 Ascend-Disconnect-Cause : Integer Value = 100 }07/07/2003 14:21:34 Ascend-Disconnect-Cause : Integer Value = 45 }07/07/2003 14:22:31 Ascend-Disconnect-Cause : Integer Value = 45 }07/07/2003 14:23:02 Ascend-Disconnect-Cause : Integer Value = 45 }07/07/2003 14:23:32 Ascend-Disconnect-Cause : Integer Value = 100 }07/07/2003 14:23:49 Ascend-Disconnect-Cause : Integer Value = 185 }07/07/2003 14:24:36 Ascend-Disconnect-Cause : Integer Value = 45 }07/07/2003 14:25:04 Ascend-Disconnect-Cause : Integer Value = 45 }07/07/2003 14:25:37 Ascend-Disconnect-Cause : Integer Value = 11 }07/07/2003 14:25:53 Ascend-Disconnect-Cause : Integer Value = 185 }07/07/2003 14:26:07 Ascend-Disconnect-Cause : Integer Value = 11 }07/07/2003 14:27:40 Ascend-Disconnect-Cause : Integer Value = 45 }07/07/2003 14:28:19 Ascend-Disconnect-Cause : Integer Value = 185 }07/07/2003 14:29:04 Ascend-Disconnect-Cause : Integer Value = 11 }07/07/2003 14:29:14 Ascend-Disconnect-Cause : Integer Value = 45 }07/07/2003 14:30:08 Ascend-Disconnect-Cause : Integer Value = 45 }07/07/2003 14:30:35 Ascend-Disconnect-Cause : Integer Value = 45 }07/07/2003 14:30:55 Ascend-Disconnect-Cause : Integer Value = 45 }07/07/2003 14:31:51 Ascend-Disconnect-Cause : Integer Value = 45 }07/07/2003 14:32:34 Ascend-Disconnect-Cause : Integer Value = 45 }07/07/2003 14:35:14 Ascend-Disconnect-Cause : Integer Value = 100 }07/07/2003 14:35:58 Ascend-Disconnect-Cause : Integer Value = 11 }07/07/2003 14:37:56 Ascend-Disconnect-Cause : Integer Value = 45 }07/07/2003 14:38:57 Ascend-Disconnect-Cause : Integer Value = 185 }07/07/2003 14:40:55 Ascend-Disconnect-Cause : Integer Value = 45 }07/07/2003 14:41:38 Ascend-Disconnect-Cause : Integer Value = 45 }07/07/2003 14:42:40 Ascend-Disconnect-Cause : Integer Value = 45 }07/07/2003 14:42:49 Ascend-Disconnect-Cause : Integer Value = 185 }07/07/2003 14:43:39 Ascend-Disconnect-Cause : Integer Value = 45 }07/07/2003 14:44:55 Ascend-Disconnect-Cause : Integer Value = 45 }07/07/2003 14:45:02 Ascend-Disconnect-Cause : Integer Value = 45 }07/07/2003 14:45:15 Ascend-Disconnect-Cause : Integer Value = 45 }07/07/2003 14:47:20 Ascend-Disconnect-Cause : Integer Value = 100 }07/07/2003 14:47:20 Ascend-Disconnect-Cause : Integer Value = 45 }07/07/2003 14:48:22 Ascend-Disconnect-Cause : Integer Value = 45 }07/07/2003 14:48:48 Ascend-Disconnect-Cause : Integer Value = 45 }07/07/2003 14:49:22 Ascend-Disconnect-Cause : Integer Value = 45 }07/07/2003 14:49:36 Ascend-Disconnect-Cause : Integer Value = 45 }07/07/2003 14:50:57 Ascend-Disconnect-Cause : Integer Value = 11 }07/07/2003 14:51:48 Ascend-Disconnect-Cause : Integer Value = 45 }07/07/2003 14:51:56 Ascend-Disconnect-Cause : Integer Value = 45 }07/07/2003 14:52:10 Ascend-Disconnect-Cause : Integer Value = 45 }07/07/2003 14:52:12 Ascend-Disconnect-Cause : Integer Value = 185 }07/07/2003 14:52:55 Ascend-Disconnect-Cause : Integer Value = 45 }07/07/2003 14:54:25 Ascend-Disconnect-Cause : Integer Value = 45 }07/07/2003 14:55:27 Ascend-Disconnect-Cause : Integer Value = 185 }07/07/2003 14:55:58 Ascend-Disconnect-Cause : Integer Value = 45 }07/07/2003 14:56:08 Ascend-Disconnect-Cause : Integer Value = 185 }07/07/2003 14:56:48 Ascend-Disconnect-Cause : Integer Value = 45 }07/07/2003 14:56:58 Ascend-Disconnect-Cause : Integer Value = 45 }07/07/2003 14:59:55 Ascend-Disconnect-Cause : Integer Value = 45 }07/07/2003 15:00:16 Ascend-Disconnect-Cause : Integer Value = 45 }07/07/2003 15:00:28 Ascend-Disconnect-Cause : Integer Value = 185 }07/07/2003 15:00:32 Ascend-Disconnect-Cause : Integer Value = 45 }07/07/2003 15:02:07 Ascend-Disconnect-Cause : Integer Value = 45 }07/07/2003 15:02:16 Ascend-Disconnect-Cause : Integer Value = 45 }07/07/2003 15:03:05 Ascend-Disconnect-Cause : Integer Value = 45 }07/07/2003 15:03:44 Ascend-Disconnect-Cause : Integer Value = 41 }07/07/2003 15:04:24 Ascend-Disconnect-Cause : Integer Value = 185 }07/07/2003 15:04:30 Ascend-Disconnect-Cause : Integer Value = 100 }07/07/2003 15:05:03 Ascend-Disconnect-Cause : Integer Value = 45 }07/07/2003 15:06:10 Ascend-Disconnect-Cause : Integer Value = 100 }07/07/2003 15:06:16 Ascend-Disconnect-Cause : Integer Value = 45 }07/07/2003 15:07:03 Ascend-Disconnect-Cause : Integer Value = 100 }07/07/2003 15:07:21 Ascend-Disconnect-Cause : Integer Value = 45 }07/07/2003 15:07:25 Ascend-Disconnect-Cause : Integer Value = 45 }07/07/2003 15:08:24 Ascend-Disconnect-Cause : Integer Value = 45 }07/07/2003 15:08:28 Ascend-Disconnect-Cause : Integer Value = 11 }07/07/2003 15:08:41 Ascend-Disconnect-Cause : Integer Value = 45 }07/07/2003 15:09:39 Ascend-Disconnect-Cause : Integer Value = 185 }07/07/2003 15:10:58 Ascend-Disconnect-Cause : Integer Value = 45 }07/07/2003 15:12:07 Ascend-Disconnect-Cause : Integer Value = 45 }07/07/2003 15:12:30 Ascend-Disconnect-Cause : Integer Value = 45 }07/07/2003 15:13:14 Ascend-Disconnect-Cause : Integer Value = 185 }07/07/2003 15:13:26 Ascend-Disconnect-Cause : Integer Value = 45 }07/07/2003 15:14:00 Ascend-Disconnect-Cause : Integer Value = 45 }07/07/2003 15:14:49 Ascend-Disconnect-Cause : Integer Value = 45 }07/07/2003 15:14:51 Ascend-Disconnect-Cause : Integer Value = 185 }07/07/2003 15:15:00 Ascend-Disconnect-Cause : Integer Value = 45 }07/07/2003 15:15:01 Ascend-Disconnect-Cause : Integer Value = 45 }07/07/2003 15:15:19 Ascend-Disconnect-Cause : Integer Value = 185 }07/07/2003 15:16:28 Ascend-Disconnect-Cause : Integer Value = 185 }07/07/2003 15:16:32 Ascend-Disconnect-Cause : Integer Value = 185 }07/07/2003 15:16:45 Ascend-Disconnect-Cause : Integer Value = 42 }07/07/2003 15:17:17 Ascend-Disconnect-Cause : Integer Value = 45 }07/07/2003 15:17:23 Ascend-Disconnect-Cause : Integer Value = 10 }07/07/2003 15:17:29 Ascend-Disconnect-Cause : Integer Value = 42 }07/07/2003 15:17:38 Ascend-Disconnect-Cause : Integer Value = 185 }07/07/2003 15:17:52 Ascend-Disconnect-Cause : Integer Value = 100 }07/07/2003 15:18:39 Ascend-Disconnect-Cause : Integer Value = 45 }07/07/2003 15:19:03 Ascend-Disconnect-Cause : Integer Value = 45 }07/07/2003 15:19:07 Ascend-Disconnect-Cause : Integer Value = 45 } }Sorry for the long post, I just wanted to see if you guys feel that this is }what I should be seeing as far as disconnect codes for the last half hour }assuming everything is good. } }-Drew } }++ Ascend Users Mailing List ++ }To unsubscribe: send unsubscribe to ascend-users-request@bungi.com }Archives: http://www.nexial.com/mailinglists/ } Hurricane Computer Products, Inc. Quality Computer Sales & Repair Cables, and Computer Accessories 352-483-2306 Voice M-F 9a-6p Sat 11a-4p 352-357-0381 Fax 352-636-1286 Cell Phone (6a-1a EST 7 Days) http://www.hurricane-computers.com ++ Ascend Users Mailing List ++ To unsubscribe: send unsubscribe to ascend-users-request@bungi.com Archives: http://www.nexial.com/mailinglists/ From troy at psknet.com Mon Jul 7 19:52:01 2003 From: troy at psknet.com (Troy Settle) Date: Tue Jan 18 13:57:51 2005 Subject: [Ascend] RE: (ASCEND) Ok ;-) I think the lines are configured properly, but. In-Reply-To: Message-ID: <001101c344e8$85feb6f0$0100a8c0@tws> If those 185's are from a wide variety of users, it may indicate that there's something wrong with the options on the trunks (either Telco or ISP side). Here's a breakdown on most of the other numbers: 11 - DCD Detected but went inactive 45 - Peer request termination 42 - Authentication failure 100 - Idle timeout If you're getting Idle timeouts after just 2 minutes, check Answer/Defaults, as the Max's default idle limit is 120 seconds. You need to adjust this to something more reasonable like 0 or 1800. If you search Google for Ascend-Disconnect-Cause and Ascend-Connect-Progress, you'll find lists of codes. Those 2 codes will tell you exactly what's going on with individual calls and can also help you identify larger problems if you examine all your data. -- Troy Settle Pulaski Networks http://www.psknet.com 540.994.4254 ~ 866.477.5638 Pulaski Chamber 2002 Small Business Of The Year > -----Original Message----- > From: owner-ascend-users@max.bungi.com > [mailto:owner-ascend-users@max.bungi.com] On Behalf Of Craig Salmond > Sent: Monday, July 07, 2003 5:07 PM > To: Drew Weaver > Cc: 'ascend-users@max.bungi.com' > Subject: Re: (ASCEND) Ok ;-) I think the lines are configured > properly, but. > > > On Mon, 7 Jul 2003, Drew Weaver wrote: > > 45's are normal cleaning. 185 is no reason specified (Far end > hung up) [Line noise, customer picked up extention] > > > } I'm kind of paranoid at one point I saw the number of > users go up to > }49, and now its back down to 37, you wouldn't think that the > number of users > }would vary that much from hour to hour would you? > } > }Here are the disconnect cause codes for the last 30 minutes: > } > }07/07/2003 14:02:19 Ascend-Disconnect-Cause : Integer Value = 185 > }07/07/2003 14:02:22 Ascend-Disconnect-Cause : Integer Value = 185 > }07/07/2003 14:02:51 Ascend-Disconnect-Cause : Integer Value = 185 > }07/07/2003 14:03:14 Ascend-Disconnect-Cause : Integer Value = 185 > }07/07/2003 14:03:25 Ascend-Disconnect-Cause : Integer Value = 185 > }07/07/2003 14:03:31 Ascend-Disconnect-Cause : Integer Value = 185 > }07/07/2003 14:03:49 Ascend-Disconnect-Cause : Integer Value = 185 > }07/07/2003 14:04:06 Ascend-Disconnect-Cause : Integer Value = 185 > }07/07/2003 14:04:14 Ascend-Disconnect-Cause : Integer Value = 185 > }07/07/2003 14:04:16 Ascend-Disconnect-Cause : Integer Value = 185 > }07/07/2003 14:04:51 Ascend-Disconnect-Cause : Integer Value = 185 > }07/07/2003 14:05:17 Ascend-Disconnect-Cause : Integer Value = 45 > }07/07/2003 14:05:25 Ascend-Disconnect-Cause : Integer Value = 11 > }07/07/2003 14:05:41 Ascend-Disconnect-Cause : Integer Value = 45 > }07/07/2003 14:05:48 Ascend-Disconnect-Cause : Integer Value = 185 > }07/07/2003 14:05:50 Ascend-Disconnect-Cause : Integer Value = 185 > }07/07/2003 14:05:56 Ascend-Disconnect-Cause : Integer Value = 100 > }07/07/2003 14:05:59 Ascend-Disconnect-Cause : Integer Value = 185 > }07/07/2003 14:06:05 Ascend-Disconnect-Cause : Integer Value = 185 > }07/07/2003 14:06:52 Ascend-Disconnect-Cause : Integer Value = 185 > }07/07/2003 14:06:53 Ascend-Disconnect-Cause : Integer Value = 185 > }07/07/2003 14:06:56 Ascend-Disconnect-Cause : Integer Value = 185 > }07/07/2003 14:06:57 Ascend-Disconnect-Cause : Integer Value = 185 > }07/07/2003 14:07:19 Ascend-Disconnect-Cause : Integer Value = 45 > }07/07/2003 14:07:22 Ascend-Disconnect-Cause : Integer Value = 185 > }07/07/2003 14:07:22 Ascend-Disconnect-Cause : Integer Value = 185 > }07/07/2003 14:07:22 Ascend-Disconnect-Cause : Integer Value = 185 > }07/07/2003 14:07:22 Ascend-Disconnect-Cause : Integer Value = 185 > }07/07/2003 14:07:22 Ascend-Disconnect-Cause : Integer Value = 185 > }07/07/2003 14:07:22 Ascend-Disconnect-Cause : Integer Value = 185 > }07/07/2003 14:07:22 Ascend-Disconnect-Cause : Integer Value = 185 > }07/07/2003 14:07:22 Ascend-Disconnect-Cause : Integer Value = 185 > }07/07/2003 14:07:22 Ascend-Disconnect-Cause : Integer Value = 185 > }07/07/2003 14:07:22 Ascend-Disconnect-Cause : Integer Value = 185 > }07/07/2003 14:07:22 Ascend-Disconnect-Cause : Integer Value = 185 > }07/07/2003 14:07:23 Ascend-Disconnect-Cause : Integer Value = 185 > }07/07/2003 14:07:23 Ascend-Disconnect-Cause : Integer Value = 185 > }07/07/2003 14:07:23 Ascend-Disconnect-Cause : Integer Value = 185 > }07/07/2003 14:07:23 Ascend-Disconnect-Cause : Integer Value = 185 > }07/07/2003 14:07:23 Ascend-Disconnect-Cause : Integer Value = 185 > }07/07/2003 14:07:33 Ascend-Disconnect-Cause : Integer Value = 185 > }07/07/2003 14:07:53 Ascend-Disconnect-Cause : Integer Value = 185 > }07/07/2003 14:08:11 Ascend-Disconnect-Cause : Integer Value = 185 > }07/07/2003 14:08:34 Ascend-Disconnect-Cause : Integer Value = 45 > }07/07/2003 14:09:19 Ascend-Disconnect-Cause : Integer Value = 185 > }07/07/2003 14:09:21 Ascend-Disconnect-Cause : Integer Value = 185 > }07/07/2003 14:09:25 Ascend-Disconnect-Cause : Integer Value = 185 > }07/07/2003 14:09:29 Ascend-Disconnect-Cause : Integer Value = 185 > }07/07/2003 14:09:37 Ascend-Disconnect-Cause : Integer Value = 45 > }07/07/2003 14:10:00 Ascend-Disconnect-Cause : Integer Value = 45 > }07/07/2003 14:10:20 Ascend-Disconnect-Cause : Integer Value = 45 > }07/07/2003 14:10:25 Ascend-Disconnect-Cause : Integer Value = 45 > }07/07/2003 14:10:38 Ascend-Disconnect-Cause : Integer Value = 185 > }07/07/2003 14:11:24 Ascend-Disconnect-Cause : Integer Value = 45 > }07/07/2003 14:13:43 Ascend-Disconnect-Cause : Integer Value = 42 > }07/07/2003 14:14:09 Ascend-Disconnect-Cause : Integer Value = 185 > }07/07/2003 14:14:25 Ascend-Disconnect-Cause : Integer Value = 11 > }07/07/2003 14:14:28 Ascend-Disconnect-Cause : Integer Value = 42 > }07/07/2003 14:14:42 Ascend-Disconnect-Cause : Integer Value = 45 > }07/07/2003 14:15:19 Ascend-Disconnect-Cause : Integer Value = 42 > }07/07/2003 14:15:39 Ascend-Disconnect-Cause : Integer Value = 42 > }07/07/2003 14:15:46 Ascend-Disconnect-Cause : Integer Value = 45 > }07/07/2003 14:16:18 Ascend-Disconnect-Cause : Integer Value = 42 > }07/07/2003 14:16:25 Ascend-Disconnect-Cause : Integer Value = 45 > }07/07/2003 14:16:54 Ascend-Disconnect-Cause : Integer Value = 185 > }07/07/2003 14:17:36 Ascend-Disconnect-Cause : Integer Value = 45 > }07/07/2003 14:17:36 Ascend-Disconnect-Cause : Integer Value = 42 > }07/07/2003 14:17:38 Ascend-Disconnect-Cause : Integer Value = 185 > }07/07/2003 14:18:55 Ascend-Disconnect-Cause : Integer Value = 100 > }07/07/2003 14:19:10 Ascend-Disconnect-Cause : Integer Value = 45 > }07/07/2003 14:19:24 Ascend-Disconnect-Cause : Integer Value = 100 > }07/07/2003 14:19:25 Ascend-Disconnect-Cause : Integer Value = 185 > }07/07/2003 14:20:44 Ascend-Disconnect-Cause : Integer Value = 100 > }07/07/2003 14:21:34 Ascend-Disconnect-Cause : Integer Value = 45 > }07/07/2003 14:22:31 Ascend-Disconnect-Cause : Integer Value = 45 > }07/07/2003 14:23:02 Ascend-Disconnect-Cause : Integer Value = 45 > }07/07/2003 14:23:32 Ascend-Disconnect-Cause : Integer Value = 100 > }07/07/2003 14:23:49 Ascend-Disconnect-Cause : Integer Value = 185 > }07/07/2003 14:24:36 Ascend-Disconnect-Cause : Integer Value = 45 > }07/07/2003 14:25:04 Ascend-Disconnect-Cause : Integer Value = 45 > }07/07/2003 14:25:37 Ascend-Disconnect-Cause : Integer Value = 11 > }07/07/2003 14:25:53 Ascend-Disconnect-Cause : Integer Value = 185 > }07/07/2003 14:26:07 Ascend-Disconnect-Cause : Integer Value = 11 > }07/07/2003 14:27:40 Ascend-Disconnect-Cause : Integer Value = 45 > }07/07/2003 14:28:19 Ascend-Disconnect-Cause : Integer Value = 185 > }07/07/2003 14:29:04 Ascend-Disconnect-Cause : Integer Value = 11 > }07/07/2003 14:29:14 Ascend-Disconnect-Cause : Integer Value = 45 > }07/07/2003 14:30:08 Ascend-Disconnect-Cause : Integer Value = 45 > }07/07/2003 14:30:35 Ascend-Disconnect-Cause : Integer Value = 45 > }07/07/2003 14:30:55 Ascend-Disconnect-Cause : Integer Value = 45 > }07/07/2003 14:31:51 Ascend-Disconnect-Cause : Integer Value = 45 > }07/07/2003 14:32:34 Ascend-Disconnect-Cause : Integer Value = 45 > }07/07/2003 14:35:14 Ascend-Disconnect-Cause : Integer Value = 100 > }07/07/2003 14:35:58 Ascend-Disconnect-Cause : Integer Value = 11 > }07/07/2003 14:37:56 Ascend-Disconnect-Cause : Integer Value = 45 > }07/07/2003 14:38:57 Ascend-Disconnect-Cause : Integer Value = 185 > }07/07/2003 14:40:55 Ascend-Disconnect-Cause : Integer Value = 45 > }07/07/2003 14:41:38 Ascend-Disconnect-Cause : Integer Value = 45 > }07/07/2003 14:42:40 Ascend-Disconnect-Cause : Integer Value = 45 > }07/07/2003 14:42:49 Ascend-Disconnect-Cause : Integer Value = 185 > }07/07/2003 14:43:39 Ascend-Disconnect-Cause : Integer Value = 45 > }07/07/2003 14:44:55 Ascend-Disconnect-Cause : Integer Value = 45 > }07/07/2003 14:45:02 Ascend-Disconnect-Cause : Integer Value = 45 > }07/07/2003 14:45:15 Ascend-Disconnect-Cause : Integer Value = 45 > }07/07/2003 14:47:20 Ascend-Disconnect-Cause : Integer Value = 100 > }07/07/2003 14:47:20 Ascend-Disconnect-Cause : Integer Value = 45 > }07/07/2003 14:48:22 Ascend-Disconnect-Cause : Integer Value = 45 > }07/07/2003 14:48:48 Ascend-Disconnect-Cause : Integer Value = 45 > }07/07/2003 14:49:22 Ascend-Disconnect-Cause : Integer Value = 45 > }07/07/2003 14:49:36 Ascend-Disconnect-Cause : Integer Value = 45 > }07/07/2003 14:50:57 Ascend-Disconnect-Cause : Integer Value = 11 > }07/07/2003 14:51:48 Ascend-Disconnect-Cause : Integer Value = 45 > }07/07/2003 14:51:56 Ascend-Disconnect-Cause : Integer Value = 45 > }07/07/2003 14:52:10 Ascend-Disconnect-Cause : Integer Value = 45 > }07/07/2003 14:52:12 Ascend-Disconnect-Cause : Integer Value = 185 > }07/07/2003 14:52:55 Ascend-Disconnect-Cause : Integer Value = 45 > }07/07/2003 14:54:25 Ascend-Disconnect-Cause : Integer Value = 45 > }07/07/2003 14:55:27 Ascend-Disconnect-Cause : Integer Value = 185 > }07/07/2003 14:55:58 Ascend-Disconnect-Cause : Integer Value = 45 > }07/07/2003 14:56:08 Ascend-Disconnect-Cause : Integer Value = 185 > }07/07/2003 14:56:48 Ascend-Disconnect-Cause : Integer Value = 45 > }07/07/2003 14:56:58 Ascend-Disconnect-Cause : Integer Value = 45 > }07/07/2003 14:59:55 Ascend-Disconnect-Cause : Integer Value = 45 > }07/07/2003 15:00:16 Ascend-Disconnect-Cause : Integer Value = 45 > }07/07/2003 15:00:28 Ascend-Disconnect-Cause : Integer Value = 185 > }07/07/2003 15:00:32 Ascend-Disconnect-Cause : Integer Value = 45 > }07/07/2003 15:02:07 Ascend-Disconnect-Cause : Integer Value = 45 > }07/07/2003 15:02:16 Ascend-Disconnect-Cause : Integer Value = 45 > }07/07/2003 15:03:05 Ascend-Disconnect-Cause : Integer Value = 45 > }07/07/2003 15:03:44 Ascend-Disconnect-Cause : Integer Value = 41 > }07/07/2003 15:04:24 Ascend-Disconnect-Cause : Integer Value = 185 > }07/07/2003 15:04:30 Ascend-Disconnect-Cause : Integer Value = 100 > }07/07/2003 15:05:03 Ascend-Disconnect-Cause : Integer Value = 45 > }07/07/2003 15:06:10 Ascend-Disconnect-Cause : Integer Value = 100 > }07/07/2003 15:06:16 Ascend-Disconnect-Cause : Integer Value = 45 > }07/07/2003 15:07:03 Ascend-Disconnect-Cause : Integer Value = 100 > }07/07/2003 15:07:21 Ascend-Disconnect-Cause : Integer Value = 45 > }07/07/2003 15:07:25 Ascend-Disconnect-Cause : Integer Value = 45 > }07/07/2003 15:08:24 Ascend-Disconnect-Cause : Integer Value = 45 > }07/07/2003 15:08:28 Ascend-Disconnect-Cause : Integer Value = 11 > }07/07/2003 15:08:41 Ascend-Disconnect-Cause : Integer Value = 45 > }07/07/2003 15:09:39 Ascend-Disconnect-Cause : Integer Value = 185 > }07/07/2003 15:10:58 Ascend-Disconnect-Cause : Integer Value = 45 > }07/07/2003 15:12:07 Ascend-Disconnect-Cause : Integer Value = 45 > }07/07/2003 15:12:30 Ascend-Disconnect-Cause : Integer Value = 45 > }07/07/2003 15:13:14 Ascend-Disconnect-Cause : Integer Value = 185 > }07/07/2003 15:13:26 Ascend-Disconnect-Cause : Integer Value = 45 > }07/07/2003 15:14:00 Ascend-Disconnect-Cause : Integer Value = 45 > }07/07/2003 15:14:49 Ascend-Disconnect-Cause : Integer Value = 45 > }07/07/2003 15:14:51 Ascend-Disconnect-Cause : Integer Value = 185 > }07/07/2003 15:15:00 Ascend-Disconnect-Cause : Integer Value = 45 > }07/07/2003 15:15:01 Ascend-Disconnect-Cause : Integer Value = 45 > }07/07/2003 15:15:19 Ascend-Disconnect-Cause : Integer Value = 185 > }07/07/2003 15:16:28 Ascend-Disconnect-Cause : Integer Value = 185 > }07/07/2003 15:16:32 Ascend-Disconnect-Cause : Integer Value = 185 > }07/07/2003 15:16:45 Ascend-Disconnect-Cause : Integer Value = 42 > }07/07/2003 15:17:17 Ascend-Disconnect-Cause : Integer Value = 45 > }07/07/2003 15:17:23 Ascend-Disconnect-Cause : Integer Value = 10 > }07/07/2003 15:17:29 Ascend-Disconnect-Cause : Integer Value = 42 > }07/07/2003 15:17:38 Ascend-Disconnect-Cause : Integer Value = 185 > }07/07/2003 15:17:52 Ascend-Disconnect-Cause : Integer Value = 100 > }07/07/2003 15:18:39 Ascend-Disconnect-Cause : Integer Value = 45 > }07/07/2003 15:19:03 Ascend-Disconnect-Cause : Integer Value = 45 > }07/07/2003 15:19:07 Ascend-Disconnect-Cause : Integer Value = 45 > } > }Sorry for the long post, I just wanted to see if you guys > feel that this is > }what I should be seeing as far as disconnect codes for the > last half hour > }assuming everything is good. > } > }-Drew > } > }++ Ascend Users Mailing List ++ > }To unsubscribe: send unsubscribe to > ascend-users-request@bungi.com > }Archives: http://www.nexial.com/mailinglists/ > } > > Hurricane Computer Products, Inc. > Quality Computer Sales & Repair > Cables, and Computer Accessories > 352-483-2306 Voice M-F 9a-6p Sat 11a-4p > 352-357-0381 Fax > 352-636-1286 Cell Phone (6a-1a EST 7 Days) > http://www.hurricane-computers.com > > ++ Ascend Users Mailing List ++ > To unsubscribe: send unsubscribe to > ascend-users-request@bungi.com > Archives: http://www.nexial.com/mailinglists/ > ++ Ascend Users Mailing List ++ To unsubscribe: send unsubscribe to ascend-users-request@bungi.com Archives: http://www.nexial.com/mailinglists/ From d.rodriguez_ay at pobox.com Wed Jul 9 16:24:01 2003 From: d.rodriguez_ay at pobox.com (Doe Rodriguez) Date: Tue Jan 18 13:57:51 2005 Subject: [Ascend] (ASCEND) Why dont you like me? Message-ID: <2.2.32.2003070921004600d6190b@pobox.com> An HTML attachment was scrubbed... URL: http://shadowknight.real-time.com/pipermail/rte-ascend/attachments/20030709/0a28527c/attachment.html From opportunity at aol.com Thu Jul 10 10:31:01 2003 From: opportunity at aol.com (Nick Nolte) Date: Tue Jan 18 13:57:51 2005 Subject: [Ascend] (ASCEND) CALL Message-ID: <200307101520.IAA01044@max.bungi.com> 1-646-218-1200..- ...U.N.I.V.E.R.S.I.T.Y----DIPL.O.M.AS--- F.r.o.m ..p.r.e.s.t.i.g.i.o.u.s., non-accredited u.n.i.v.e.r.s.i.t.i.e.s. based on your present knowledge and life experience. No required .t.e.s.t.s, classes, books, or interviews. Bachelors, masters, MBA, and doctorate (P.h.D.) d.i.p.l.o.m.a.s. available in the field of your choice. No one is turned down.Confidentiality assured. C.A.L.L N O W!!! 1-646-218-1200..- 24 hours a day, 7 days a week, including Sundays and holidays. no: aosdfgihafdsgn43534 ++ Ascend Users Mailing List ++ To unsubscribe: send unsubscribe to ascend-users-request@bungi.com Archives: http://www.nexial.com/mailinglists/ From max_and_tnt at hotmail.com Thu Jul 10 11:57:01 2003 From: max_and_tnt at hotmail.com (Joe Max) Date: Tue Jan 18 13:57:51 2005 Subject: [Ascend] Re: (ASCEND) Line Quality - E1 & Series56 Message-ID: Since it is an E1 line, make sure that the MAX is strapped for the proper impedance. Look in the hardware manual for details. >When users dial-in to my Max 4000 (all users are anolog modem users, we >dont need isdn etc.), the modem takes very long time to handshake and >mostly it fails to connect after about a minute. I tried various AT >answer strings but no good result. When I checked the modem diagnostics, >it showed a very poor Line Quality and RX level. But when I put the same >E1 line into other RAS servers (working Patton and Total Control), it >works just fine, the line quality shows very good. > >Could this be an incompatibility issue? I have checked with the Telco >(the telco uses Siemens switches, though I dont know other details) and >they have no such complaints for any other E1 connections. > >Any help will be highly appreciated. ++ Ascend Users Mailing List ++ To unsubscribe: send unsubscribe to ascend-users-request@bungi.com Archives: http://www.nexial.com/mailinglists/ From max_and_tnt at hotmail.com Thu Jul 10 12:26:01 2003 From: max_and_tnt at hotmail.com (Joe Max) Date: Tue Jan 18 13:57:51 2005 Subject: [Ascend] Re: (ASCEND) Re: disconnected users Message-ID: You should probably ask Lucent LWS, but I think that the only way to do that is using SS7/IPDC. >Hi >hopes every one be fine.I need a little help.Is there >any method to route incoming calls to some other >Maxtnt. >the situation here is like this > E1/pri local circuit >User ----> Maxtnt 1----------------> maxtnt 2 > >Now my users are getting login to Maxtnt 1 , i want to >change this thing that user login to Maxtnt 2. >So what could be the option ? is there some device or >Max's card which support call routing to some other >Max tnt.If any one know any material about call >routing i ll highly appreciate the help. ++ Ascend Users Mailing List ++ To unsubscribe: send unsubscribe to ascend-users-request@bungi.com Archives: http://www.nexial.com/mailinglists/ From vharpertk at cw.net Fri Jul 11 14:03:01 2003 From: vharpertk at cw.net (Virgie T. Harper) Date: Tue Jan 18 13:57:51 2005 Subject: [Ascend] (ASCEND) Just one more thing.. jf743lmpd0re Message-ID: <431701c34807$d57d02fc$a1d299ef@txj8na3> An HTML attachment was scrubbed... URL: http://shadowknight.real-time.com/pipermail/rte-ascend/attachments/20030711/5c6c8bfb/attachment.htm From d.farid at aloline.com Sat Jul 12 02:08:01 2003 From: d.farid at aloline.com (Djema Farid) Date: Tue Jan 18 13:57:51 2005 Subject: [Ascend] (ASCEND) MAX6000 boot problem Message-ID: <2729.213.181.53.27.1057992631.squirrel@mail.aloline.com> Hello, I have a problem with Lucent Max 6000. The only message in the boot sequence is : MAX6000 Boot PROM 1.4 MAX6000 Boot PROM 1.4 MAX6000 Boot PROM 1.4 I have test several solutions but without success. Would you give me please any proposition to examine or any one to contact. thankyou ++ Ascend Users Mailing List ++ To unsubscribe: send unsubscribe to ascend-users-request@bungi.com Archives: http://www.nexial.com/mailinglists/ From lmolo at fsmail.net Sat Jul 12 19:39:01 2003 From: lmolo at fsmail.net (LAWRENCE MOLO) Date: Tue Jan 18 13:57:51 2005 Subject: [Ascend] (ASCEND) YOUR COPERATION Message-ID: <200307130020.RAA15606@max.bungi.com> Attn: I am BARRISTER LAWRENCE MOLO Solicitor. I am the Personal Attorney to ENGR: J.M. PEDRO a national of your country, who used to work with shell development company in Bakassi Cameroun. On the 21st of April 2000, my client,his wife And their three children were involved in a car accident along Yaounde/Bakassi Express Road.unfortunately they All lost their lives in the event of the accident, Since then I have made several enquiries to your Embassy to locate any of my clients extended relatives, this has also proved unsuccessful.After these several unsuccessful attempts, I decided to trace his relatives over the Internet, to locate any member of his family but of no avail, hence I contacted you. I contacted you to assist in repartrating the money and property left behind by my client before they get confiscated or declared unserviceable by the bank where this huge deposits were lodged.Particularly, the Bank where the deceased had an account valued at about 15 million dollars. Conseqently,The bank issued me a notice to provide the next of kin or have the account confiscated within the next ten official working days. since i have been unsuccesfull in locating the the relatives for over 3 years now I seek your consent to present you as the next of kin of the deceased since you are from the same country so that the proceeds of this account valued at $15 million dollars can be paid to you and then you and i can share the money. 50% to me and 40% to you ESQ: LAWRENCE MOLO I have all necessary legal documents that can be used to back up any claim we may make. All I require is your honest cooperation to enable us see this deal through. I guarantee that this will be executed under a legitimate arrangement that will protect you from any breach of the law. Best regard LAWRENCE MOLO ++ Ascend Users Mailing List ++ To unsubscribe: send unsubscribe to ascend-users-request@bungi.com Archives: http://www.nexial.com/mailinglists/ From d.farid at aloline.com Thu Jul 17 11:06:23 2003 From: d.farid at aloline.com (Djema Farid) Date: Tue Jan 18 13:57:51 2005 Subject: [Ascend] (ASCEND) MAX6000 boot problem Message-ID: <3116.213.181.53.27.1058456815.squirrel@mail.aloline.com> Hello, I have a problem with Lucent Max 6000. The only message in the boot sequence is : MAX6000 Boot PROM 1.4 MAX6000 Boot PROM 1.4 MAX6000 Boot PROM 1.4 I have test several solutions but without success. Would you give me please any proposition to examine or any one to contact. thankyou ++ Ascend Users Mailing List ++ To unsubscribe: send unsubscribe to ascend-users-request@bungi.com Archives: http://www.nexial.com/mailinglists/ From troy at psknet.com Fri Jul 18 07:26:00 2003 From: troy at psknet.com (Troy Settle) Date: Tue Jan 18 13:57:52 2005 Subject: [Ascend] RE: (ASCEND) MAX6000 boot problem In-Reply-To: <3116.213.181.53.27.1058456815.squirrel@mail.aloline.com> Message-ID: <002e01c34d25$2d79c6b0$0100a8c0@tws> Djema, Search google for 'ascend 6000 nindy.' Follow the instructions to reload the firmware on the box. If that fails to help you, contact Lucent technical support for assistance (don't tell them about the NINDY though). If neither of those work, you probably just need to go buy yourself a new 6000 chassis. I'd imagine that you can find one for less than $2k without a problem. In fact, I see some idiot on Ebay that has a bunch listed for $100 starting and no reserve. Too bad I'm using the TNT now, I'd probably take them all at that price. -- Troy Settle Pulaski Networks http://www.psknet.com 540.994.4254 ~ 866.477.5638 Pulaski Chamber 2002 Small Business Of The Year > -----Original Message----- > From: owner-ascend-users@max.bungi.com > [mailto:owner-ascend-users@max.bungi.com] On Behalf Of Djema Farid > Sent: Thursday, July 17, 2003 11:47 AM > To: owner-ascend-users@max.bungi.com > Cc: ascend-users@max.bungi.com > Subject: (ASCEND) MAX6000 boot problem > > > Hello, > I have a problem with Lucent Max 6000. The only message in the boot > sequence is : > MAX6000 Boot PROM 1.4 > MAX6000 Boot PROM 1.4 > MAX6000 Boot PROM 1.4 > I have test several solutions but without success. > Would you give me please any proposition to examine or any one to > contact. > thankyou > > > > ++ Ascend Users Mailing List ++ > To unsubscribe: send unsubscribe to > ascend-users-request@bungi.com > Archives: http://www.nexial.com/mailinglists/ > ++ Ascend Users Mailing List ++ To unsubscribe: send unsubscribe to ascend-users-request@bungi.com Archives: http://www.nexial.com/mailinglists/ From ahmiqs at yahoo.com Fri Jul 25 00:15:02 2003 From: ahmiqs at yahoo.com (Schahzad Zafar) Date: Tue Jan 18 13:57:52 2005 Subject: [Ascend] (ASCEND) Serial link and routing issue Message-ID: <20030725042735.45152.qmail@web12108.mail.yahoo.com> Hi friends I am working to findout if i can skip cisco and configure serial link with Max TNT and Max 6000.Is there any one who can help how it ld be possible.What i found out is , that Max TNT has Swan card option and Max 6000 has v.35 interface.Also an important thing is routing , how we can route traffic to some specific interface instead ip-address .In routing profile , TnT has gateway-address option.But is there any possibility of interface routing like cisco ? Thanx for help Regards __________________________________ Do you Yahoo!? Yahoo! SiteBuilder - Free, easy-to-use web site design software http://sitebuilder.yahoo.com ++ Ascend Users Mailing List ++ To unsubscribe: send unsubscribe to ascend-users-request@bungi.com Archives: http://www.nexial.com/mailinglists/ From salesinfobrc at sympatico.ca Sun Jul 27 14:52:01 2003 From: salesinfobrc at sympatico.ca (Béret Rouge Canada Inc.) Date: Tue Jan 18 13:57:52 2005 Subject: [Ascend] (ASCEND) Love is everything - help for those who love others Message-ID: <20030727185300.PZQF26593.tomts23-srv.bellnexxia.net@Sender> For those who help and love others: Tired of selling bad chocolate for your fund raising charity/activities. Sell classical music CDs. Sell Mozart, Beethoven, Chopin, etc. CDs. Any fund raising such as cancer research, victim of criminal act, help for the poor, etc. funds raising are welcome. Have what you like on the CD: organization name, logo, phone number, web site, anything in full color. For 500 copies @ $3.00 USD/CD but for Canadian buyer ($3.00 Can+GST (+Quebec TVQ if in Quebec)). For a 1000 CDs @ $2.50 and 2000 CDs @ $2.00. Include the mass production CDs copy. Custom duties might apply outside Canada. Shipping cost will be added. E-mail us for free sample as MP3. Regards, Michel Thivierge, CEO B?ret Rouge Canada Inc. 819-986-3617 205 rue Des Bernaches Gatineau, sector Masson-Angers, Qc, Canada J8M 1K8 ++ Ascend Users Mailing List ++ To unsubscribe: send unsubscribe to ascend-users-request@bungi.com Archives: http://www.nexial.com/mailinglists/ From max_and_tnt at hotmail.com Sun Jul 27 21:10:02 2003 From: max_and_tnt at hotmail.com (Joe Max) Date: Tue Jan 18 13:57:52 2005 Subject: [Ascend] Re: (ASCEND) Serial link and routing issue Message-ID: If all you have is a V.35 interface, the swan or swan-2 cards will be your only choices. If you have the choice, get the swan-2. The other one is no longer supported. BTW, swan cards support FR and PPP links only. Verify that the remote end of the circuit will support either one of those two choices. If the other end is a MAX6000, you will be ok. TAOS does not support interface routing. You need to assign an IP address to each interface and use the _remote_ IP address for routing. It is a little different than Cisco's but it works just the same. Cheers, -Joe >Date: Thu, 24 Jul 2003 21:27:35 -0700 (PDT) > >Hi friends >I am working to findout if i can skip cisco and >configure serial link with Max TNT and Max 6000.Is >there any one who can help how it ld be possible.What >i found out is , that Max TNT has Swan card option and >Max 6000 has v.35 interface.Also an important thing is >routing , how we can route traffic to some specific >interface instead ip-address .In routing profile , TnT >has gateway-address option.But is there any >possibility of interface routing like cisco ? _________________________________________________________________ Add photos to your e-mail with MSN 8. Get 2 months FREE*. http://join.msn.com/?page=features/featuredemail ++ Ascend Users Mailing List ++ To unsubscribe: send unsubscribe to ascend-users-request@bungi.com Archives: http://www.nexial.com/mailinglists/ From rt_mena at yahoo.com Wed Jul 30 10:24:01 2003 From: rt_mena at yahoo.com (Robert Mena) Date: Tue Jan 18 13:57:52 2005 Subject: [Ascend] (ASCEND) newbie : help with max tnt ip pool configuration Message-ID: <20030730150714.20761.qmail@web9807.mail.yahoo.com> Hi, I have an already running MAX for which I must change the configuration in order to add another pool and redefine the current ip-pool (adding new ips of the same "class". I've downloaded a lot of PDFs and read but they do not give sample configs clear enough for me to poke around... It's TAOS 8.0.2. Regards. PS. Please CC me directly if possible. __________________________________ Do you Yahoo!? Yahoo! SiteBuilder - Free, easy-to-use web site design software http://sitebuilder.yahoo.com ++ Ascend Users Mailing List ++ To unsubscribe: send unsubscribe to ascend-users-request@bungi.com Archives: http://www.nexial.com/mailinglists/ From skipmax at seacove.net Wed Jul 30 11:47:01 2003 From: skipmax at seacove.net (Dennis Duval) Date: Tue Jan 18 13:57:52 2005 Subject: [Ascend] Re: (ASCEND) newbie : help with max tnt ip pool configuration References: <20030730150714.20761.qmail@web9807.mail.yahoo.com> Message-ID: <002101c356b4$6badcc40$0a01a8c0@barny> Robert Mena wrote: > Hi, > > I have an already running MAX for which I must change > the configuration in order to add another pool and > redefine the current ip-pool (adding new ips of the > same "class". > Assuming you have telnetted in, and have the full access password, go into Full Access mode: CTRL-D-->Password-->Full Access-->(enter password) Then go to: Ethernet-->Mod Config-->WAN Options--> There you will see the settings for the IP pools. Basically you set a starting IP address and how many address you have. So if you only want to set up 10 IP addresses in a pool, you could set "Pool#1 start" to 1.1.1.11 and "Pool#1 Count" to 10, and this would be a pool of IP addresses containing the range 1.1.1.11 through 1.1.1.20 Dennis Duval ++ Ascend Users Mailing List ++ To unsubscribe: send unsubscribe to ascend-users-request@bungi.com Archives: http://www.nexial.com/mailinglists/ From skipmax at seacove.net Wed Jul 30 11:54:01 2003 From: skipmax at seacove.net (Dennis Duval) Date: Tue Jan 18 13:57:52 2005 Subject: [Ascend] Re: (ASCEND) newbie : help with max tnt ip pool configuration References: <20030730150714.20761.qmail@web9807.mail.yahoo.com> Message-ID: <004001c356b5$47c68e10$0a01a8c0@barny> Robert Mena wrote: > Hi, > > I have an already running MAX for which I must change > the configuration in order to add another pool and > redefine the current ip-pool (adding new ips of the > same "class". Sorry I missed the part in the subject line about it being a TNT until after I posted the previous reply. I gave instructions for a Max4000/6000. Not sure if the settings are the same on the TNT. Dennis Duval ++ Ascend Users Mailing List ++ To unsubscribe: send unsubscribe to ascend-users-request@bungi.com Archives: http://www.nexial.com/mailinglists/ From rcasta at itesm.mx Thu Jul 31 18:24:00 2003 From: rcasta at itesm.mx (Ricardo J Castaneda) Date: Tue Jan 18 13:57:52 2005 Subject: [Ascend] (ASCEND) need codes please!! Message-ID: <5.1.0.14.0.20030731141646.02200268@itesm.mx> Does Anyone know about these Ascend-Disconnect-Cause codes?? 730, 471 and 81. Thanks !! ++ Ascend Users Mailing List ++ To unsubscribe: send unsubscribe to ascend-users-request@bungi.com Archives: http://www.nexial.com/mailinglists/ From max_and_tnt at hotmail.com Thu Jul 31 23:38:00 2003 From: max_and_tnt at hotmail.com (Joe Max) Date: Tue Jan 18 13:57:52 2005 Subject: [Ascend] Re: (ASCEND) need codes please!! Message-ID: >Does Anyone know about these Ascend-Disconnect-Cause codes?? > >730, 471 and 81. From max_and_tnt at hotmail.com Thu Jul 31 23:42:01 2003 From: max_and_tnt at hotmail.com (Joe Max) Date: Tue Jan 18 13:57:52 2005 Subject: [Ascend] Re: (ASCEND) newbie : help with max tnt ip pool configuration Message-ID: > > I have an already running MAX for which I must change > > the configuration in order to add another pool and > > redefine the current ip-pool (adding new ips of the > > same "class". >Sorry I missed the part in the subject line about it being a TNT until >after >I posted the previous reply. I gave instructions for a Max4000/6000. Not >sure if the settings are the same on the TNT. For TNTs, pools are defined in the IP-GLOBAL profile: admin> read ip-global admin> list [in IP-GLOBAL] ... (shown with defaults, not my values) ... must-accept-address-assign = no pool-summary = no pool-chaining = no pool-ospf-adv-type = type-1 pool-base-address = [ 0.0.0.0 0.0.0.0 0.0.0.0 0.0.0.0 0.0.0.0 0.0.0.0 0.0.0.0 0+ assign-count = [ 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 + pool-name = [ "" "" "" "" "" "" "" "" "" "" "" "" "" "" "" "" "" "" "" "" "" ""+ ... _________________________________________________________________ STOP MORE SPAM with the new MSN 8 and get 2 months FREE* http://join.msn.com/?page=features/junkmail ++ Ascend Users Mailing List ++ To unsubscribe: send unsubscribe to ascend-users-request@bungi.com Archives: http://www.nexial.com/mailinglists/