Hello, sometimes before i asked for some help to configure a Cisco 1603 as RAS-Client to a MAX-TNT thanks for the help i got. But now as it works the customer wants to have callback from the TNT. Everything i do the two devices do not connect after the callback. Has anyone done this before ? The RADIUS Profile for this connection on the TNT side and the configuration of the 1603 i add to this mail below. Thanks in before Heribert Kruell Remote Access Administration Stadtwerke Duesseldorf AG Germany Navis-Radius-Profile for TNT router1603 Password = "pass" Framed-Protocol = PPP, Ascend-Data-Svc = Switched-64K, Ascend-Callback = Callback-Yes, Ascend-Dial-Number = 9xxxxxxx, Ascend-Send-Auth = Send-Auth-PAP, Ascend-Authen-Alias = "max", Ascend-Send-Passwd = "pass", Ascend-Idle-Limit = 90, Ascend-Data-Filter = "ip in forward dstip 192.168.0.0/24", Ascend-Data-Filter = "ip in drop" Config des Cisco 1603 Current configuration: ! version 11.3 service timestamps debug uptime service timestamps log uptime service password-encryption ! hostname router1603 ! enable secret 5 $1$ZQ7t$BHrGUVqRmEa.vph2TNZG2. enable password 7 1046191613 ! username max password 7 105E0009 username router1603 password 7 02160D4B0200 isdn switch-type basic-net3 ! ! interface Ethernet0 ip address 192.168.250.1 255.255.255.0 ip nat inside ! interface BRI0 no ip address encapsulation ppp dialer pool-member 1 ! interface Dialer1 ip address negotiated no ip proxy-arp ip nat outside encapsulation ppp no ip split-horizon dialer remote-name max dialer idle-timeout 180 dialer string 8007 dialer hold-queue 10 dialer load-threshold 255 outbound dialer pool 1 dialer-group 1 ppp callback request ppp pap sent-username rt0012 password 7 01030F14520D0717 ! ip classless ip route 192.168.0.0 255.255.255.0 Dialer1 access-list 1 permit 192.168.250.0 0.0.0.255 dialer-list 1 protocol ip permit ! line con 0 line vty 0 4 password 7 0503160037 login ! end on a ping the cisco says: ping 192.168.0.10 Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 192.168.0.10, timeout is 2 seconds: 21:05:51: %ISDN-6-LAYER2UP: Layer 2 for Interface BR0, TEI 69 changed to up. 21:05:53: %LINK-3-UPDOWN: Interface BRI0:1, changed state to up 21:05:53: %DIALER-6-BIND: Interface BRI0:1 bound to profile Dialer1 21:05:53: %LINK-3-UPDOWN: Interface BRI0:1, changed state to down 21:05:53: %DIALER-6-UNBIND: Interface BRI0:1 unbound from profile Dialer1.. 21:05:57: %DIALER-6-BIND: Interface BRI0:2 bound to profile Dialer1 21:05:57: %LINK-3-UPDOWN: Interface BRI0:2, changed state to up 21:05:57: %LINK-3-UPDOWN: Interface BRI0:1, changed state to up 21:05:57: %DIALER-6-BIND: Interface BRI0:1 bound to profile Dialer1 21:05:57: %LINK-3-UPDOWN: Interface BRI0:1, changed state to down 21:05:57: %DIALER-6-UNBIND: Interface BRI0:1 unbound from profile Dialer1.. Success rate is 0 percent (0/5) 21:06:01: %LINK-3-UPDOWN: Interface BRI0:1, changed state to up 21:06:01: %DIALER-6-BIND: Interface BRI0:1 bound to profile Dialer1 21:06:01: %LINK-3-UPDOWN: Interface BRI0:1, changed state to down 21:06:01: %DIALER-6-UNBIND: Interface BRI0:1 unbound from profile Dialer1 21:06:06: %DIALER-6-BIND: Interface BRI0:1 bound to profile Dialer1 21:06:06: %LINK-3-UPDOWN: Interface BRI0:1, changed state to up 21:06:09: %LINEPROTO-5-UPDOWN: Line protocol on Interface BRI0:1, changed state to up 21:06:12: %ISDN-6-CONNECT: Interface BRI0:1 is now connected to 8007 21:06:22: %DIALER-6-UNBIND: Interface BRI0:2 unbound from profile Dialer1 21:06:22: %ISDN-6-DISCONNECT: Interface BRI0:2 disconnected from 8007 , call la sted 24 seconds 21:06:22: %LINK-3-UPDOWN: Interface BRI0:2, changed state to down ++ Ascend Users Mailing List ++ To unsubscribe: send unsubscribe to ascend-users-request at bungi.com Archives: http://www.nexial.com/mailinglists/