We are trying to move a CT1 from a PM-3 to a Max 6096. The CT1 is currently
setup as Trunk-side, B8ZS, ESF, Wink-Start..
When we dial in to the max, we receive a busy signal.
When we telnet into the max, we see it attempting to connect as we see the
line changine from '-' to 'r' to 'c'.
As we watch the telnet connection, we attempt to dial into the max, and we
see it picking up on two channels:
Jul 9 05:38:48 max6000 ASCEND: call 80 AN slot 7 port 5 56KR
Jul 9 05:38:48 max6000 ASCEND: call 80 CL 0K c=185 p=10
Jul 9 05:38:48 max6000 ASCEND: slot 7 port 5, line 4, channel 2, Call
Disconnected [MBID 352]
Jul 9 05:38:49 max6000 ASCEND: call 81 AN slot 7 port 6 56KR
Jul 9 05:38:49 max6000 ASCEND: call 81 CL 0K c=185 p=10
Jul 9 05:38:49 max6000 ASCEND: slot 7 port 6, line 4, channel 3, Call
Disconnected [MBID 353]
The telnet to the max shows the first line go from '-' to 'r' to 'c', but
the second line goes from '-' to 'c', so my guess is that the switch is
seeing the first line busy, and rolling it to the next line.
Another thing that we are seeing is that CH 24 is repeatedly going into an
answer state. From the syslogs we see repeated entries for CH 24 (different
'call' numbers):
Jul 9 05:36:08 max6000 ASCEND: call 74 AN slot 6 port 15 56KR
Jul 9 05:36:28 max6000 ASCEND: call 74 CL 0K c=185 p=31
Jul 9 05:36:28 max6000 ASCEND: slot 6 port 15, line 4, channel 24, Call
Disconnected [MBID 346]
Which it then ends up in the Answer stage.
lqqqqqqqqqqqqqqqqqqqqk
x20-200 1234567890 x
x L2/LA ---------- x
x 12345678901234 x
x -------------* x
lqqqqqqqqqqqqqqqqqqqqk
I currently have the Max 6096 configured as:
20-100 Line Config
20-1** Factory
Name=Factory
1st Line=Trunk
2nd Line=Trunk
Line 1 ....
Sig Mode=Inband
NFAS ID num=N/A
Rob Ctl=Wink-Start
Switch Type=N/A
ISDN TE/NT mode=N/A
Framing Mode=ESF
Front End=CSU
Encoding=B8ZS
FDL=None
Length=N/A
Buildout=0 dB
Clock Source=Yes
Collect DNIS/ANI=Yes
InterDigit Timeout=3000
Pbx Type=N/A
Delete Digits=N/A
Add Number=N/A
Call-by-Call=N/A
T1-PRI:PRI # Type=Unknown
T1-PRI:NumPlanID =ISDN
Ans #=N/A
Ans Service=N/A
Input Sample count=N/A
Send Disc=0
Net2Net Incoming Calls...
Net2Net ChanGroup ID...
Line Provisioning=None
Ch 1=Switched
Ch 1 #=8831
Ch 1 Slot=3
Ch 1 Prt/Grp=0
Ch 1 TrnkGrp=N/A
:
:
Ch 16=Switched
Ch 16 #=8831
Ch 16 Slot=3
Ch 16 Prt/Grp=0
Ch 16 TrnkGrp=N/A
Ch 17=Switched
Ch 17 #=8831
Ch 17 Slot=4
Ch 17 Prt/Grp=0
Ch 17 TrnkGrp=N/A
:
:
Ch 24=Switched
Ch 24 #=8831
Ch 24 Slot=4
Ch 24 Prt/Grp=0
Ch 24 TrnkGrp=N/A
Hunt-1 #=
Hunt-2 #=
Hunt-3 #=
Line 2...
:
Collect DNIS/ANI=No
InterDigit Timeout=N/A
:
T1-PRI:NumPlanID =Unknown
:
Ch 1=Switched
Ch 1 #=
Ch 1 Slot=4
Ch 1 Prt/Grp=0
Ch 1 TrnkGrp=N/A
:
Ch 8=Switched
Ch 8 #=
Ch 8 Slot=4
Ch 8 Prt/Grp=0
Ch 8 TrnkGrp=N/A
Ch 9=Switched
Ch 9 #=
Ch 9 Slot=5
Ch 9 Prt/Grp=0
Ch 9 TrnkGrp=N/A
:
Ch 24=Switched
Ch 24 #=
Ch 24 Slot=5
Ch 24 Prt/Grp=0
Ch 24 TrnkGrp=N/A
This is all I have configured on the MAX 6096 in regards to the CT1
configuration (no changes to the modem slots (3-8)).
What do I need to change to get the CT1 working on the MAX 6096?
Scot
++ Ascend Users Mailing List ++
To unsubscribe: send unsubscribe to ascend-users-request at bungi.com
Archives: http://www.nexial.com/mailinglists/