Faisal: Do you know what WCCP is? That doesn't consume much CPU on the router because it doesn't scan all traffic to look for port 80, it just redirects all port 80 requests on the Serials to X numbers of cache you have running with WCCP. I have it that way and it works perfect. If you want you can email me and I'll send you the configurations and modules that I have running. Jose F. Escobar Ayustar Corporation 787-440-3232 jescobar at ayustar.com -----Original Message----- From: owner-ascend-users at max.bungi.com [mailto:owner-ascend-users at max.bungi.com]On Behalf Of Faisal §. Naik Sent: Wednesday, November 20, 2002 5:18 PM To: Troy Settle Cc: ascend-users at max.bungi.com Subject: Re: (ASCEND) TNT config-commands Importance: High Thanks for the replies Troy.. I'll check these out soon. The reason i am moving away from the idea of redirecting the traffic on router is the high CPU utilization factor of the router. I am already running such a setup. Anywya.. lets see wht can be doen with the TNT Thanks once again ----- Original Message ----- From: "Troy Settle" <troy at psknet.com> To: "'Faisal S. Naik'" <faisal at hamdard.net.pk>; "'Ascend-users'" <ascend-users at max.bungi.com> Sent: Friday, November 22, 2002 4:56 PM Subject: RE: (ASCEND) TNT config-commands > > > -----Original Message----- > > From: owner-ascend-users at max.bungi.com > > [mailto:owner-ascend-users at max.bungi.com] On Behalf Of Faisal S. Naik > > Sent: Friday, November 22, 2002 12:40 AM > > To: Ascend-users > > Subject: (ASCEND) TNT config-commands > > > > > > Hello All, > > I need to monitor the modem success rate and call success rate for all > > incoming user calls on my TNT. Is there a specific command to > > check this or > > do i need to enable some debug? > > > > The best way to do this, is via radius and/or syslog accounting. I've > set my radius server to record all accounting data to a SQL server, from > which, I can quickly generate reports on connect speeds, disconnect > causes, connection failures, etc... In order to see failed connection > attempts, you'll need to set > external-auth/rad-acct-client/acct-stop-only = yes. > > > > 2ndly what type of message do i need to enable for syslog messages to > > display E1 link down messages on my syslog server. > > Log/syslog-level = critical > > If you have an SNMP server, you can enable trap messages, which should > be more efficient than scanning syslog for such issues. > > > > > And finally i need to define policy routing on the TNT box to > > redirect all > > port 80 traffic to my proxy server forcefully, how to go about it? > > I don't know if you can set up a port redirect in the TNT, but I do know > that you can set up filters to block port 80 traffic to anything except > your proxies (which is a good idea in general). The only drawback to > this, is that your users will need to manually set their proxy server > address. > > I would recommend either setting your proxy server between the TNT and > border router, or do the redirect on the border router itself (there's a > sample configuration in the Squid FAQ and/or manual (which would apply > even if you're not using squid). > > > > > TIA > > > > Regards, > > ----------- > > Faisal §. Naik > > Karachi. > > I hope this helps, > > -- > Troy Settle > Pulaski Networks > 540.994.4254 - 866.477.5638 > http://www.psknet.com > ++ Ascend Users Mailing List ++ To unsubscribe: send unsubscribe to ascend-users-request at bungi.com Archives: http://www.nexial.com/mailinglists/ ++ Ascend Users Mailing List ++ To unsubscribe: send unsubscribe to ascend-users-request at bungi.com Archives: http://www.nexial.com/mailinglists/