Well I tried that. If we back up a bit, if eth0 is connect to a hub, should not the hub light be lit. That is not happening. When eth1 is connected to the hub, the hub light lights. Now the "link" light lights on the nic when a cable is plugged into it. It is not the cable, because I am using the same cable for both testing eth1 and eth0. Any other thoughts? John Miller -----Original Message----- From: Eric Stanley [mailto:barnabas at knicknack.net] Sent: Sunday, August 12, 2001 6:16 PM To: tclug-list at mn-linux.org Subject: Re: [TCLUG] NIC Card If I understand what you were trying to do, your routing probably prevented that from working (unless, of course, you changed). What you could do is leave both cards up, put them both on your internal network and try pinging the eth0 address (192.168.0.4) from your windows box. I think that even if all traffic for your internal network is routed through eth1, pinging the eth0 card will work in this case. Someone correct me if I'm wrong. The other thing you could try is to change the routing so that traffic for your internal network routes through eth0. Then the ping test to 192.168.0.4 should work. HTH, Eric On Sun, Aug 12, 2001 at 06:01:03PM -0500, Miller, John wrote: > Yes I have two cards. I thought of that and called AT&T (isp) and asked > which card was registered for connection. It was eth0. > > Is there a way to bring up eth0 with an internal address so I can try to > ping another computer. I tried to bring it up by issuing > > ifconfig eth0 192.168.0.4 up > > This address belongs to another box this is currently down. I decided > to try that address because it was already set up in the /etc/hosts > file. I brought down the eth1 card and tried to ping 192.168.0.2 which > is my windows box. eth1 could ping it, no luck on the eth0 > > John Miller > > -----Original Message----- > From: Eric Stanley [mailto:barnabas at knicknack.net] > Sent: Sunday, August 12, 2001 5:43 PM > To: tclug-list at mn-linux.org > Subject: Re: [TCLUG] NIC Card > > > It looks like you have two cards -- are they the same kind of card? > If so, it is possible that the BIOS switched them around so that what > was eth0 is now eth1 and vice versa. Might that be the case? > > Eric > > On Sun, Aug 12, 2001 at 05:34:43PM -0500, Miller, John wrote: > > I wrote earlier this week about my mb dying. After further trials, it > > still lives. I took the system apart so I could get to the connector > > better and plugged it in and it worked. The ps died. > > > > Now I have my system reassembled and the NIC that I use to connect to > > the internet seems not to be working. Drivers for both cards are > > loaded. /proc/pci lists them both When I plug the cable in, the link > > light comes on on the back of the card but does not light up the hub. > I > > have swap the the cord on the hub, nothing. When I bring eth0 up with > > ifconfig eth0 up, I get all the information. > > > > The card is a netgear FA311. It has served me well. > > > > Anyone have any ideas, > > > > TIA > > > > John Miller > > _______________________________________________ > > tclug-list mailing list > > tclug-list at mn-linux.org > > https://mailman.mn-linux.org/mailman/listinfo/tclug-list > > > _______________________________________________ > tclug-list mailing list > tclug-list at mn-linux.org > https://mailman.mn-linux.org/mailman/listinfo/tclug-list > _______________________________________________ > tclug-list mailing list > tclug-list at mn-linux.org > https://mailman.mn-linux.org/mailman/listinfo/tclug-list > _______________________________________________ tclug-list mailing list tclug-list at mn-linux.org https://mailman.mn-linux.org/mailman/listinfo/tclug-list